How to Repair Broken Car Keys
Nobody likes calling the dealership to buy spare parts for their vehicle. It's costly and can take a while for them to get the part you require.
To save money, you can attempt a DIY solution to your broken car key. All you require is a paperclip and some wire.
Drill a hole into the broken end of the key
There's nothing more annoying than a car key that is broken. It's not just a huge hassle to get into your vehicle but also you won't be able to start the engine. You can fix it yourself, without having to contact an expert. You can apply super glue to connect the two ends of your key. This method should only be used as a last resort since it could cause damage to the ignition or lock.
First, you'll need to cut the nail to a suitable length. You will need to use it as a connector so it shouldn't be too long or too thick. Then, you can drill a hole into the broken part of your key. Do it slowly and with care. If you don't take care you could cause more damage to the problem. Avoid using a drill for the ignition because it can cause serious damage.
Another method of fixing damaged car keys is to make use of a small piece metal, such as pins or screws to push the two ends of the key to each other. You can also use pliers, but be careful not to damage the car key.
Then, you can try using a small amount of clear tape to keep the two ends of the key together. This will stop the key from breaking even more, and it will also provide you with more control over it when you attempt to take it out of the lock.
If none of these solutions work, call a locksmith immediately. A locksmith will be able to remove the key from your car lock and supply you with an alternative. They are accessible 24/7 and can respond quickly to your call. They can also assist you in saving money by offering discounts on key replacements. In some instances they may even design the new keys on the spot so you don't have to wait for a while before getting back on the road.
Connect to a connector
If your key gets damaged in the lock of your car, it can be a nightmare. It is impossible to unlock or open your vehicle and you may be required to pay a large amount of money to get it repaired. Fortunately, there are a few things you can do to help to fix the issue.
Connecting a connector is among of the most effective solutions for damaged keys. The connector will grasp the damaged end of the key and pull it out of the lock. There are many hardware stores that sell it, and it is a great way to get back on the road. But, you need to be careful while using it. Make sure it's not in the ignition lock and not touching the battery of your car.
A second solution is to carefully remove the key fob and then examine it. If you notice that the buttons appear to be not in the right place or are damaged Try changing them. The key fob is likely to see lots of use and its buttons are likely to get jostled around.
If you can't fix your key, it might be best to contact a locksmith. A locksmith can rekey your keys at your address. They can also replace the chip on the key which is essential for cars with a newer model. You should also check the warranty of your car to find out if or not you can get a replacement for the key.
The most frequent reason for a car key that is broken is that the transponder chip inside the fob has stopped functioning. This can cause issues starting the car because the key will not send a signal from the car ignition cylinder. It is possible to reprogramme the chip by yourself, however this is a time-consuming and expensive procedure.
If the car key you have a microchip in it that you can't replace without reprogramming the chip. This can be done at the dealership or manufacturer however, it could cost more than a locksmith. It is also worth checking the warranty to determine if you can have the key replaced for free.
The key can be glued to each other
When your car key breaks, it can be a huge trouble. As opposed to a flat tire, or a dead battery, this is one of the few problems that can hinder you from getting where you want to go. You might have to take public transportation or contact a friend to arrange a ride, which can be difficult. Luckily, there are ways to repair your car key to be on your way.
Glues might seem like the most effective solution, but they are not the best choice for this situation. There is not enough surface area to glue the key back together. The area where it broke must be able to withstand the pressure when it is turned. It's possible to weld the key back together however, this isn't recommended unless you're an experienced automotive locksmith. It can damage your ignition tumbler and you'll have to buy another key.
The best method is to remove the broken part from the lock by using pliers. Be careful not to bind the pieces and break them. After you've removed the broken pieces, you'll be able to bring them to a locksmith or the dealership.
You can also fix a broken key by applying superglue to both ends of the key. Make sure you align the broken sections correctly prior to applying the glue. It is important to wait a few seconds after applying the glue before attempting to remove the key. Once key fob repairs is dry, you can test it to determine if the key works.
If you don't have any tools or spare keys the only option is to call an auto locksmith. A professional locksmith will be able to remove the broken key quickly and effortlessly. This will save you a lot of time and money.
A professional will be able to determine the cause of your car key break and help you find the best solution. They can also program the new car key for you and supply you with one.
Pull the key out
If a fragment of a damaged car key remains protruding from the lock, you might be in a position to remove it yourself. However, excessive twisting of a stuck key could cause further damage within the lock and may require professional assistance. To avoid this, spray the keyway first with some graphite or lubricant. Try to grab the visible part of the key using the needle-nosed pliers. If the pliers fail to hold the broken piece of key, you might need to purchase an under-$10 tool specifically designed for this task such as a key extractor kit. These kits come with a variety of tools that are made to fit a specific keyway. Select the one that fits the lock you are having trouble with and insert it until it reaches just above the first cut of the damaged key. Then you can use the hook of the tool to secure the key, and pull.
Another alternative is to use a heated glue stick to mould the broken key piece. Once the glue is set, it will be easier to pull out. However this method is a risk because it could cause the key to fall off completely. If you decide to try it, ask a family member or co-worker to watch the lock while you are away.
If the lock is a standard cylinder, you might be able insert the pin or clip into the back and push out the damaged part. This is done by looking at the back of the of the cylinder and finding the slot.
You could also try key extractor tools or other specialty tools available in hardware stores. These tools aren't big enough to enter the lock, but they're sturdy and can aid you in getting your broken key out of your car. Select the right size tool for your keyway, and follow the directions.
If you're not able to use the special tools then you can try the traditional way of turning a screwdriver, or other flathead tools. Use a small enough screwdriver to fit inside the lock. You could also use a bent paper clip to remove the damaged key from the lock of your car.